View B66202B1106T001_4863044.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EF coil formers
Series/Type:
E 13/7/4
The following products presented in this data sheet are being withdrawn. Ordering Code B66202J1106T001 B66202A1108T001 Substitute Product B66202B1106T001 B66202B1108T001 Date of Withdrawal 2010-01-29 2010-01-29 Deadline Last Orders 2010-04-30 2010-04-30 Last Shipments 2010-07-30 2010-07-30
For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.
E 13/7/4 (EF 12.6) Core

B66305
3.7 _ 0.3
4.5+0.3
To IEC 61246 For miniature transformers Available with SMD coil former E cores with high permeability for common-mode chokes and broadband applications Delivery mode: single units Magnetic characteristics (per set)
_ 0.4 12.6 +0.5
6.5 _ 0.2
6 l/A le Ae Amin Ve
= 2.39 mm-1 = 29.6 mm = 12.4 mm2 = 12.2 mm2 = 367 mm3
3.7 _ 0.3 8.9+0.6
g
FEK0089-9
Approx. weight 2 g/set
Ungapped Material N30 T46 N27 N87 AL value nH 1000 +30/-20% 3600 r30% 800 +30/-20% 850 +30/-20% Pe 1900 6839 1510 1620 < 0.40 (200 mT, 100 kHz, 100 C) < 0.20 (200 mT, 100 kHz, 100 C) PV W/set Ordering code B66305G0000X130 B66305F0000X146 B66305G0000X127 B66305G0000X187
Gapped Material N27 g mm 0.04 r0.01 AL value approx. nH 250 Pe 454 Ordering code B66305G0040X127
The AL value in the table applies to a core set comprising one ungapped core (dimension g = 0) and one gapped core (dimension g > 0).
Please read Cautions and warnings and Important notes at the end of this document.
2
09/06
E 13/7/4 (EF 12.6) Core
Calculation factors (for formulas, see "E cores: general information") Material Relationship between air gap - AL value K1 (25 C) N27 N87 Validity range: 28.4 28.4 K2 (25 C) - 0.676 - 0.676 Calculation of saturation current K3 (25 C) 36.5 37.5 K4 (25 C) - 0.847 - 0.796 K3 (100 C) K4 (100 C) 33.2 32.1 - 0.865 - 0.873
B66305
K1, K2: 0.03 mm < s < 1.00 mm K3, K4: 30 nH < AL < 260 nH
Please read Cautions and warnings and Important notes at the end of this document.
3
09/06
E 13/7/4 (EF 12.6) Accessories
Coil former (magnetic axis horizontal or vertical) GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 C), color code black Valox 420-SE0 (R) >E45329 (M)@, GE PLASTICS B V Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 C, 3.5 s Winding: see Data Book 2007, chapter "Processing notes, 2.1" Squared pins. Yoke Material: Coil former Version Horizontal Vertical Sections 1 1 AN mm2 11.6 11.6 lN mm 27.2 27.2 AR value P: 80.6 80.6 Pins 8 6 B66202B1108T001 B66202B1106T001 B66202A2010X000 Stainless spring steel (0.2 mm) Ordering code Material:
B66202
Yoke (ordering code per piece, 2 are required) Horizontal version
14.2 _ 0.2
3.9+0.1
8.7 _ 0.2 3.9+0.1
8.7 _ 0.2 0.60.1 0.60.1
10.4 max.
3.5 _ 0.5
1.6 _ 0.1
5.1_ 0.2
0.45 1+0.1
5.1_ 0.2 8 5
3 x 3.81 = 11.43
16.2 _ 0.25
14.2
Hole arrangement View in mounting direction
1
4 10.16
FEK0449-5-E
Please read Cautions and warnings and Important notes at the end of this document.
3.81
4
01/10
E 13/7/4 (EF 12.6) Accessories
Vertical version
B66202
Hole arrangement View in mounting direction
Yoke
0.5 max.
3.20.15
3.7 _ 0.2
_ 0.2 13.2 +0.5
5.2 _ 0.2
FEK0450-8
Please read Cautions and warnings and Important notes at the end of this document.
5
05/08
E 13/7/4 (EF 12.6) Accessories
SMD coil former with gullwing terminals Material: GFR liquid crystal polymer (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 C), color code black Vectra C 130 >E83005 (M)@, TICONA Solderability: to IEC 60068-2-58, test Td, method 6 (Group 3): 245 C, 3 s Resistance to soldering heat: to IEC 60068-2-58, test Td, method 6 (Group 3): 255 C, 10 s permissible soldering temperature for wire-wrap connection on coil former: 400 C, 1 s Winding: see Data Book 2007, chapter "Processing notes, 2.1" Sections 1 2 AN mm2 13.0 10.2 lN mm 27 27 AR value P: 71 91 Terminals 10 10 Ordering code B66306C1010T001 B66306C1010T002
B66306
8,5 _ 0,1 7,3 1,6
9,1 max. 1 x 45
13 _ 0,2 8,7 _ 0,2
3,90,1
3,90,1
13 _ 0,2 19,4 _ 0,2 Empfehlung fur das Recommended Leiterplattenlayout PCB layout
0,60,05 4 x 2,54 = 10,16
5,1 2,54
5,1
20,3
FEK0291-X
Please read Cautions and warnings and Important notes at the end of this document.
6
09/06
2,54
2,5
10,16
1,2
E 13/7/4 (EF 12.6) Accessories
Cover plate
For stamping and for improved processing on assembly machines See under SMD coil former for material and resistance to soldering heat
B66414
Ordering code Cover plate B66414A7000X000
0,5 max.
12,80,1
FEK0260-3
Please read Cautions and warnings and Important notes at the end of this document.
6,60,1
1,80,1
7
09/06
Ferrites and accessories Cautions and warnings
Mechanical stress and mounting Ferrite cores have to meet mechanical requirements during assembling and for a growing number of applications. Since ferrites are ceramic materials one has to be aware of their special behavior under mechanical load. Just like any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing or tensile load. Especially fast cooling rates under ultrasonic cleaning, high static and cyclic loads can cause cracks or failure of the ferrite cores. For detailed information see Data Book 2007, chapter "General - Definitions, 8.1". Effects of core combination on AL value Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent that the initial permeability is dependent on the stress state of the core. The higher the stresses are in the core, the lower the value for the initial permeability. Thus, the embedding medium should offer the greatest possible elasticity. For detailed information see Data Book 2007, chapter "General - Definitions, 8.2". Heating up Ferrites can run hot during operation at higher flux densities and higher frequencies. NiZn-materials The magnetic properties of NiZn-materials can change irreversibly when exposed to strong magnetic fields. Processing notes - The start of the winding process should be soft. Otherwise, the flanges may be destroyed. - Excessive winding forces may damage the flanges or squeeze the tube so that the cores can no longer be mounted. - Excessive soldering time at high temperature (>300 C) may affect coplanarity or pin arrangement. - Not following the processing notes for soldering of the J-leg terminals may cause solderability problems at the transformer because of contamination with tin oxide (SnO) from the tin bath or burned insulation from the wire. For detailed information see Data Book 2007, chapter "Processing notes, 2.2". - The dimensions of the pin hole arrangement are fixed and should be understood as an ideal recommendation for drilling the printed circuit board. In order to avoid problems when mounting the transformer, customers should make allowances for manufacturing tolerances in the drilling and pick-and-place processes by increasing the diameter of the pin holes.
8
01/10
Important notes
The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, MiniBlue, MiniCell, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 9 01/10

▲Up To Search▲

Price & Availability of B66202B1106T001

	To Download B66202B1106T001 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .